TPMC810

Two Independent Channel Extended CAN Bus

  • Standard single-width 32 bit PMC module
  • 2 independent CAN bus channels
  • CAN specification 2.0B supported
  • On board termination can be configured
  • Front panel I/O (2 DB9 male connectors) and P14 I/O

 

Product status: Active

Operating Temperature Range -40 °C to +85 °C RoHS compliant

The TPMC810 is a standard single-width 32 bit PMC with two independent CAN bus channels, isolated from system logic and from each other.

Two Philips SJA1000 CAN controllers (CAN specification 2.0B supported) are used.

CAN High Speed transceivers are used for the CAN bus I/O interface. An on board termination option (DIP switches) is provided for each CAN bus channel allowing to configure on board termination and pass through mode.

Each channel can generate an interrupt on INTA. Interrupts can be enabled and disabled separately.

The TPMC810 provides front panel I/O via two DB9 male connectors and rear panel I/O via P14.

Software support (TDRV010-SW-xx) for different operating systems is available.

Mechanical Interface PCI Mezzanine Card (PMC) Interface, Single Size
Electrical Interface PCI Rev. 3.0 compatible, 33 MHz / 32 bit PCI, 3.3V and 5V PCI Signaling Voltage
PCI Target Chip TEWS PCI Interface FPGA
CAN Controller 2x SJA1000 @ 16 MHz (Philips/NXP)
CAN Transceiver 2x TJA1050 (Philips/NXP)
Number of CAN Bus Channels 2 (Isolated against each other)
CAN Bus Interface CAN High Speed (ISO11898-2)
CAN Data Transmission Rate Minimum: 60kbaud (TJA1050 TXD Dominant Time-Out Feature)
Maximum: 1Mbaud
I/O Connector 2x DB9 male front connectors
PMC P14 I/O (64 pin Mezzanine connector)
Power Requirements 207mA typical @ +5V DC
Temperature Range Operating: -40 °C to +85 °C
Storage: -40 °C to +125 °C
Humidity 5-95% non-condensing
MTBF 527 122 h

MTBF values shown are based on calculation according to MIL-HDBK-217F and MIL-HDBK-217F Notice 2; Environment: GB 20°C.

The MTBF calculation is based on component FIT rates provided by the component suppliers. If FIT rates are not available, MIL-HDBK-217F and MIL-HDBK-217F Notice 2 formulas are used for FIT rate calculation.

Weight 73.3 g

PRODUCT VARIATIONS

TPMC810-10R

2 x isolated CAN Bus based on Philips SJA1000, ISO11898 Can Hig Speed, 2 x DB9 and P14 I/O

2 channel isolated CAN Bus; Standard and extended frame support; CAN-HIGH-SPEED (ISO11898); Optically isolated interfaces; Front I/O via DB-9 connectors; Rear I/O

TPMC810-20R

2 x isolated CAN Bus based on Philips SJA1000, ISO11898 Can Hig Speed, 2 x DB9 and P14 I/O with same pin assignment as TPMC816-10R

2 channel isolated CAN Bus; Standard and extended frame support; CAN-HIGH-SPEED (ISO11898); Optically isolated interfaces; Front I/O via DB-9 connectors; Rear I/O; TPMC816-10R compatible pinout

ACCESSORIES

PIM I/O Module with 50 pin Connector

SOFTWARE

Device Driver for CAN Bus Board Family with SJA1000 Controller

Data Sheet

Data Sheet

Data Sheet - Issue 2.0.0

User Manual

User Manual - Issue 2.0.0