The TCP465 is a standard 3U 32 bit CompactPCI module and offers 8 channels of high performance RS232/RS422/RS485 programmable asynchronous serial interface. The module offers front panel I/O with a HD50 SCSI-2 type connector. The TCP465-20R module offers additional J2 rear I/O.
The serial channels can be individually programmed to operate as RS232, RS422 or RS485 full duplex/half duplex interface. In addition programmable termination is provided for the RS422/RS485 interfaces. After power-up all serial I/O lines are in a high impedance state.
Each RS232 channel supports RxD, TxD, RTS, CTS and GND. RS422 and RS485 full duplex support a four wire interface (RX+, RX-, TX+, TX-) plus ground (GND). RS485 half duplex supports a two wire interface (DX+, DX-) plus ground (GND).
Each channel has 64 byte transmit and receive FIFOs to significantly reduce the overhead required to provide data to and get data from the transmitters and receivers. The FIFO trigger levels are programmable and the baud rate is individually programmable up to 921.6 kbps for RS232 channels and 5.5296 Mbps for RS422/RS485 channels. The UART offers readable FIFO levels.
All channels generate interrupts on CompactPCI interrupt INTA. For fast interrupt source detection the UART provides a special Global Interrupt Source Register.
All serial channels use ESD protected transceivers up to ±15KV.
The TCP465 can operate with 3.3V and 5.0V PCI I/O signaling voltage.
Software Support (TDRV002-SW-xx) for different operating systems is available.
||Standard 3U 32 Bit CompactPCI module conforming to
PICMG 2.0 R3.0
||PCI Rev. 2.3 compliant; 33 MHz / 32 bit PCI; 3.3V and 5V PCI Signaling Voltage
|PCI Target Chip
||Asynchronous serial interface
|Number of Channels
||Software selectable RS232, RS422, RS485 full duplex, RS485 half duplex
|Serial Channel I/O Signals
||RS232: TxD, RxD, RTS, CTS, GND
RS422/RS485 Full Duplex: TxD+/-, RxD+/-, GND
RS485 Half Duplex: Dx+/-, GND
||Software selectable 120ohms
||±15kVHuman Body Model
|Programmable Baud Rates
||RS232: up to 921.6 kbps
RS485: up to 5.5296 Mbps
||HD50 SCSI-2 type connector (e.g. AMP# 787395-5)
TCP465-20R: additional 110 pol. CompactPCI back I/O (J2)
||40 mA typical @ +5V DC (Shutdown, no load)
55 mA typical @ +5V DC (RS232, no load)
115 mA typical @ +5V DC (RS422, no load)
440 mA typical @ +5V DC (RS485 FD Master, no load)
400 mA typical @ +5V DC (RS485 HD, no load)
45 mA typical @ +3.3V DC (no load)
||Operating: -40 °C to +85 °C
Storage: -40 °C to +100 °C
||460 000 h to 490 000 h
||5 – 95% non-condensing
1) depends on variant, for further details see User Manual
8 Channel Programmable RS232/RS422/RS485, Front I/O
8 programmable RS232/RS422/RS485 serial interfaces; RS232 supports hardware handshake; RS485 half-duplex support; baudrates up to 5.5296 Mbps (921.6 kbps for RS232); Front I/O via HD50 / SCSI-2 connector
8 Channel Programmable RS232/RS422/RS485, Front and Rear I/O
8 programmable RS232/RS422/RS485 serial interfaces; RS232 supports hardware handshake; RS485 half-duplex support; baudrates up to 5.5296 Mbps (921.6 kbps for RS232); Front I/O via HD50 / SCSI-2 connector; J2 Rear I/O
HD50 / SCSI-2 Cable
HD50 / SCSI-2 Terminal Block
Cable Kit for Modules with HD50 / SCSI-2 Connector
Front panel extension for 3U cPCI boards
Device Driver for Multiple Channel Serial Interface Family