Showing 1–12 of 13 results

QMC Starter Kit

Make your first steps with the new VITA 93 - QMC mezzanine standard
- Quad UART QMC
  - Single size QMC Module
  - Multiprotocol transceiver offering RS232/RS422/RS485
  - Operating temperature -40 °C to +85 °C
  - Air-Cooled
- Dual QMC Carrier
  - Low-Profile PCIe Card
  - 2 QMC sites
  - VHDCI68 Front I/O Connector
  - Operating temperature -40 °C to +85 °C
- Cable Kit
  - 1.8 m cable with VHD68 SCSI-V male and HD68 SCSI-3 male type connector
  - 68 pin terminal block
- Device Driver
VIEW FULL SPECIFICATIONS
TPCE210

PCI Express x4, Gen 2, Dual QMC Carrier
- Low-profile PCI Express Revision 2.0 compatible module
- Cost effective solution to provide I/O in PCI Express environment
- Flexible I/O (TEWS offers a wide range of QMCs)
- Supports two single QMCs or one double QMC
- Provides QMC front panel I/O via VHDCI-68 Connector
- Management Controller for surveillance of QMC health status
VIEW FULL SPECIFICATIONS
TPCE646

Reconfigurable MPSoC with 32 x 16 bit Analog Output and 8 x 16 bit differential Analog Input
- Form Factor: X8 PCIe
  - Board size: tbd. x 98 mm
- PCI Express x8 Gen 3 Link from PCIe Card edge conector to MPSoC PL.
- Optional PCI Express x4 Gen2 Link to MPSoC PS.
- TPCE646 MPSoC options:
- -10R Xilinx XCZU11EG-1FFVC1760I
- Serial Flash for MPSoC Configuration
- FPGA clock options:
  - Local clock generator as source for the MPSoC internal PLL
- DDR4 SDRAM PL bank, 64 bit 1GB
  - (up to 8 GB)
- DDR4 SDRAM PS bank, 64 Bit 4GB
  - (up to 8 GB)
- 8 MPSoC PS Multi-Gigabit-Transceiver on a seperate Samtec FireFly© connector.
- Front I/O lines
  - 8 differential analog inputs
    - 16 bit resolution
    - 5 Msps
    - Factory calibration
  - 32 differential analog outputs
    - 16 bit resolution
    - ±10 V single ended output
    - Factory calibration
    - 4 differential digital LVDS I/O lines
- Rear I/O lines
  - 64 single ended or 32 differential rear I/O lines on a rear 68 pin Samtec QTE© connector.
  - 8 MPSoC PS Multi-Gigabit-Transceiver on two seperate rear Samtec FireFly© connector.
  - 10/100/1000 Mbps RJ45 Ethernet Interface
VIEW FULL SPECIFICATIONS
TPCE240

PCI Express Carrier for one PCIe Mini Card
- Standard height PCI Express Revision 2.0 compatible module
- Cost effective solution to provide I/O in PCI Express environment
- Flexible I/O (TEWS offers a wide range of I/O PCIe Mini Cards)
- Supports 1 PCI Express Mini Card
- Provides front panel I/O
VIEW FULL SPECIFICATIONS
TPCE260

PCI Express PMC Carrier
- Standard height PCI Express Revision 1.1 compatible module
- Cost effective solution to provide I/O in PCIexpress environment
- Flexible I/O (TEWS offers a wide range of I/O PMCs)
- PCIexpress x1 link
- Supports one single-width 32 bit PMC
- 33 MHz / 66 MHz PCI frequency (PMC site)
- Provides access to the PMC front
- Provides rear I/O (P14) through a VME P2 style connector
VIEW FULL SPECIFICATIONS
TPCE261

PCI Express x1 PMC Carrier
$1.00
- Standard height PCI Express Revision 2.0 compatible module
- Cost effective solution to provide I/O in PCIexpress environment
- Flexible I/O (TEWS offers a wide range of I/O PMCs)
- PCIexpress x1 link with 2.5 GT/s
- Supports one single-width 32 bit PMC
- 33 MHz / 66 MHz PCI frequency (PMC site)
- Provides access to the PMC front panel I/O
- Provides rear I/O (P14) through a 68 pin ERNI SMC 1.27 mm flat cable connector
VIEW FULL SPECIFICATIONS This product has multiple variants. The options may be chosen on the product page
TPCE275

PCI Express x1, Gen 1 XMC Carrier
- Standard height PCI Express Revision 1.1 compatible module
- Cost effective solution to provide I/O in PCI Express environment
- Flexible I/O (TEWS offers a wide range of I/O XMCs)
- Supports 1 single-width XMC
- Provides front panel I/O
- Provides XMC P14 rear I/O through VME P2 connector
- Provides XMC P16 rear I/O through two 50-pin flat cable connectors
- PCI Express x1 from host board to XMC
- PCIe Redriver allows safe operation of XMC module in distributed PCIe systems
VIEW FULL SPECIFICATIONS
TPCE277

PCI Express x1, Gen3 XMC Carrier
- Standard height PCI Express Revision 3.0 compatible module
- Cost effective solution to provide I/O in PCI Express environment
- Flexible I/O (TEWS offers a wide range of I/O XMCs)
- Supports 1 single-width XMC
- Provides front panel I/O
- PCI Express x1 from host board to XMC
- PCIe Gen3 Redriver allows safe operation of XMC module in distributed PCIe systems
VIEW FULL SPECIFICATIONS
TPCE278

PCI Express x4, Gen3 XMC Carrier
- Standard height PCI Express Revision 3.0 compatible module
- Cost effective solution to provide I/O in PCI Express environment
- Flexible I/O (TEWS offers a wide range of I/O XMCs)
- Supports 1 single-width XMC
- Provides front panel I/O
- Provides XMC P14 rear I/O through Tyco AMPMODU System 50 0.050x0.100 flat ribbon cable connector
- Provides XMC P16 rear I/O through two Samtec QTH-DP 0.50mm Q Pairs High Speed Ground Plane Socket Strip, Differential Pair connector
- PCI Express x4 from host board to XMC
- PCIe Gen3 Redriver allows safe operation of XMC module in distributed PCIe systems
VIEW FULL SPECIFICATIONS
TPCE280

PCI Express x8, Gen3 XMC Carrier
- Standard height, half length PCI Express Revision 3.0 compatible module
- Cost effective solution to provide I/O in PCI Express environment
- Flexible I/O (TEWS offers a wide range of I/O XMCs)
- Supports 1 single-width XMC
- Provides front panel I/O
- Provides XMC P14 rear I/O through 68-pin ERNI SMC, right angle male, 1.27mm pitch connector
- Provides XMC P16 rear I/O through two Samtec Firefly UCC8 and UEC5 connectors
- PCI Express x8 from host board to XMC
- PCIe Gen3 Redriver allows safe operation of XMC module in distributed PCIe systems
- Provides a fan mounted under the XMC slot that helps cooling the system
VIEW FULL SPECIFICATIONS
TPCE636

Reconfigurable FPGA with 16x Analog Input and 16x Analog Output
- Standard height, half-length PCI Express 2.1 compliant module
- Supports PCI Express x4 link
- User configurable FPGA (AMD Kintex™ 7)
- 1 Gbyte, 32 bit wide DDR3 SDRAM
- 64 FPGA I/O lines on back I/O connector
  - 64 single ended LVCMOS25 or 32 differential LVDS25 interface.
- 16 channels 16 bit ADC
  - Differential interface
  - Input range ±20 V
  - Sampling rate up to 5 Msps
- 16 channels 16 bit DAC
  - Output range ±10 V
- Front panel I/O via Samtec ERF8-049 Rugged EdgeRate connector
VIEW FULL SPECIFICATIONS
TPCE863

4 Channel High Speed Synch/Asynch Serial Interface
- Standard height, half-length PCI Express 1.1 compliant module
- 4 high speed serial data communication channels
- A wide range of I/O interfaces individually programmable for each channel
- Several communication protocols
  - asynchronous (with oversampling)
  - isochronous
  - HDLC
- 512 longword FIFO (512 x 32 bit) per channel
- DMA support
- Different signal encodings (NRZ, NRZI, FM0, FM1 and Manchester)
- Multiple clock sources (for a wide bitrate spectrum)
- Front panel I/O via HD68 SCSI-3 type connector
VIEW FULL SPECIFICATIONS

QMC Starter Kit

TPCE210

TPCE646

TPCE240

TPCE260

TPCE261

TPCE275

TPCE277

TPCE278

TPCE280

TPCE636

TPCE863