TXMC395

Conduction Cooled, 4 Channel 1000BASE-T Ethernet

  • Conduction Cooled single-width XMC module
  • 4 channel 1000BASE-T / 100BASE-TX / 10BASE-T
  • IPMI resource: FRU hardware definition information stored in on-board EEPROM
  • PXE and iSCSI boot (16 Mbit serial flash)
  • IEEE 1588/802.1AS Precision Time Protocol (PTP) and IEEE 802.1Qav Audio/Video Bridging (AVB) traffic shaping
  • Rear I/O via P16 – 2 channels mapped in X12d range and 2 channels mapped in X8d range (VITA46.9)

Product status: Active

The TXMC395 is a Conduction Cooled Switched Mezzanine Card (CCXMC) compatible module providing a four channel Ethernet 10Base-T / 100Base-TX / 1000Base-T interface.

A PCIe Switch provides access to the Intel I210IT Gigabit Ethernet controllers. Each Ethernet interface supports 10, 100 and 1000 Mbit/s transmission rates and is equipped with a 16 Mbit Serial Flash to support PXE and iSCSI boot.

The four Ethernet interfaces of the TXMC395 are capable of performing an auto negotiation algorithm which allows both link-partners to determine the best link-parameters. The TXMC395 supports IEEE 1588/802.1AS Precision Time Protocol (PTP) and IEEE 802.1Qav Audio/Video Bridging (AVB) traffic shaping (with software extensions).

The TXMC395-10R routes four Ethernet ports to the Back I/O P16 connector. Two ports are mapped in the X12d range and two ports are mapped in the X8d range specified in VITA46.9 standard.

All ports are galvanically isolated from the Ethernet controllers and LEDs on the board indicate the different network activities.

The module meets the requirements to operate in extended temperature range from -40°C to +85°C.

Software Support:

  • Software support for Intel I210IT at www.intel.com
  • For operating systems not supported by Intel, please contact TEWS.
Mechanical Interface Conduction Cooled Switched Mezzanine Card (CCXMC) Interface conforming to ANSI/VITA 42.0 and ANSI/VITA 20

Standard single-width (143.75 mm x 74 mm)

Electrical Interface x4 PCI Express (Specification 2.1) compliant interface conforming to ANSI/VITA 42.3
PCIe Switch PI7C9X2G608GP (Diodes Incorporated)
Gigabit Ethernet Controllers For each interface: I210-IT (Intel)
16 Mbit Serial Flashes for Boot ROM For each interface: W25Q16JV (Winbond)
Number of Channels 4
I/O Standards 10Base-T / 100Base-TX / 1000Base-T
I/O Connector Back I/O P16 (Samtec ASP-103614-04 or compatible)
Two ports mapped in X12d range and two ports mapped in X8d range (VITA46.9)
Power Requirements 600mA typical @ VPWR = +5V (four channel, no link)
app. additional 10mA to 100mA per link270mA typical @ VPWR = +12V (four channel, no link)
app. additional 4.5mA to 45mA per link
Temperature Range Operating: -40 °C to +85 °C
Storage: -40 °C to +85 °C
MTBF 922 000 h

MTBF values shown are based on calculation according to MIL-HDBK-217F and MIL-HDBK-217F Notice 2; Environment: GB 20°C.

The MTBF calculation is based on component FIT rates provided by the component suppliers. If FIT rates are not available, MIL-HDBK-217F and MIL-HDBK-217F Notice 2 formulas are used for FIT rate calculation.

Humidity 5 – 95% non-condensing
Weight 68 g

PRODUCT VARIATIONS

TXMC395-10R

4 Channel 1000BASE-T Ethernet

4 channel 1000BASE-T Ethernet; P16 back I/O; Conduction Cooled

ACCESSORIES

PIM for Gigabit Ethernet XMCs

SOFTWARE

Third Party Device Driver Support

Data Sheet

Data Sheet - Issue 1.0.2

User Manual

User Manual - Issue 1.0.1